Storing Pipe Clamps.

Storing Pip Clamps Woodsmith Tips found ==> Here

Crosscut Sled for Small Parts

Many of my woodworking projects require small parts. The challenge there is cutting the parts accurately and safely. I designed the crosscut sled shown in the photo below to be an easy solution to the problem.

The thing that separates this from other crosscut sleds is the addition of a piece of T-track in the base. The T-track holds a combination stop block and hold-down. The stop block guarantees the parts are cut identically and the hold-down prevents them from moving.

I like the sled so much I’ve even made a couple others with angled fences. These allow me to cut small mitered parts for segmented turnings.

- See more at: http://www.woodsmithtips.com/2011/12/01/crosscut-sled-for-small-parts/?utm_source=WoodsmithTips&utm_medium=email&utm_campaign=5361#sthash.UWgeO4YM.dpuf

Multipurpose Layout Tool

I like to think of a craft knife as an all-in-one cutting tool. That’s because there are so many types of interchangeable blades available (photo at below).

You can use it with a standard blade as a marking knife or switch to a thicker blade for carving and cleaning out the waste of a hinge mortise. And like a utility knife, the blades can be thrown out when they get dull. Just keep in mind that the blades are beveled on both faces.

The knife handles and blades can be purchased individually or in a set (as shown). You can find them at most craft and hobby stores.

Simple Jig Saw Tip

Simple Jig Saw Tip ==> Here

Top Mortise Tips

An easy way to cut mortises is by drilling a series of overlapping holes at the drill press. Then you can use a chisel to remove the ridges on the sides and ends.

The drawings below show how to guide the chisel to pare away the waste. This technique leaves smooth walls for a better-fitting mortise and a flat glue surface.

I start with a wide chisel on the sides. A wide blade helps keep the surface smooth, with no “steps” between cuts. Take thin shavings, starting at the tips of the ridges and move back until the wall of the mortise is smooth. By controlling the downward pressure with your dominant hand and using your opposite hand to direct the blade, you’ll quickly get a feel for it. Pivoting the chisel allows you to make fine paring cuts for a smooth wall.

With the sides cleaned up, switch to a chisel that matches the width of the mortise to square the ends.

- See more at: http://www.woodsmithtips.com/2011/09/01/top-mortise-tips/?utm_source=WoodsmithTips&utm_medium=email&utm_campaign=5085#sthash.hKvdx0kP.dpuf

Clamping Molding

Clamping Molding ==> Here

Cleaning Your Router

Cleaning Your Router ==> Here

Pegboard Tips

Pegboard Tips! ==> Here

Cut Plywood With Ease

Cutting Plywood With Ease ==> Here

Installing a Vise on Your Workbench

Installing a Vise on Your Workbench. You can View the Tip at the following Link. ==> Here

Woodsmith Tips

I'll be bringing back this winter, the Woodsmith Tips from my eMail.  I know everyone probably gets them for their own eMail, But at least some new followers or even old follers that like my blog can find them here.

ALL Post from Woodsmith Tips are NOT My Tips just incause anyone is wondering, they are copyrighted by Woodsmith I'm just sharing for everyone to view.

Probably some tips, Tricks and or hints from Woodworkers Journal and few other sites as well!  So my First post will be of some of the OLDER Woodsmith Tips I've got in my eMail!

Two Ways to Install Wood Glass Stops

Two Ways to Install Wood Glass Stops

Planing Extra Thin Stock

Planing Extra Thin Stock

Woodsmith Tip: Scroll Saw Auxiliary Table

Woodsmith Tip: Scroll Saw Auxiliary Table

Woodsmith Tip: Small Parts Clamp

Woodsmith Tip: Small Parts Clamp

Cutting a Four-Sided Taper

Cutting a Four-Sided Taper

Quick Tip Saves Time When Finishing

Quick Tip Saves Time When Finishing

Keeping Square Edges When Sanding Projects

Keeping Square Edges When Sanding Projects

Get a Clean Cut on Your Miter Saw

Get a Clean Cut on Your Miter Saw

How to Rout a Slot through the Center of a Workpiece

How to Rout a Slot through the Center of a Workpiece